靜力壓入法是根據裝配時所需壓入力的大小不同、采用夾鉗、千斤頂、手動或機動的壓力機進行，靜力壓入法一般用于錐形軸孔。由于靜力壓入法受到壓力機械的限制，在過盈較大時，施加很大的力比較困難。同時，在壓入過程中會切去聯軸器與軸之間配合面上不平的微小的凸峰，使配合面受到損壞。因此，這種方法一般應用不多。

裝配后的檢查：聯軸器在軸上裝配完后，應仔細檢查聯軸器與軸的垂直度和同軸度。一般是在聯軸器的端面和外圓設置兩塊百分表，盤車使軸轉動時，觀察聯軸器的全跳動（包括端面跳動和徑向跳動）的數值，判定聯軸器與軸的垂直度和同軸度的情況。不同轉速、不同型式的聯軸器對全跳動的要求值不同，聯軸器在軸上裝配完后，要使聯軸器全跳動的偏差值在設計要求的公差范圍內，這是聯軸器裝配的主要質量要求之一。

造成聯軸器全跳動值不符合要求的原因很多，可能由于加工造成的誤差。而對于現場裝配來說，由于鍵的裝配不當引起聯軸器與軸不同軸。鍵的正確安裝應該使鍵的兩側面與鍵槽的壁嚴密貼合，一般在裝配時用涂色法檢查，配合不好時可以用銼刀或鏟刀修復使其達到要求。鍵頂部一般有間隙，約在0.1-0.2mm左右。高速旋轉機械對于聯軸器與軸的同軸度要求高，用單鍵聯接不能有高的同軸度，用雙鍵聯接或花鍵聯接能使兩者的同軸度有改善。